You press the button, the door starts down, and then it stops, reverses, or doesn’t move at all. A garage door that won’t close is more than an annoyance. It leaves your home and car exposed, and in some cases it’s a sign of a part that’s about to fail. The good news is that many of the causes are simple and safe to check yourself. Here’s how to narrow down the problem, what you can fix on your own, and when it’s time to call a technician.
Start With the Simple Checks
Before assuming something is broken, rule out the easy stuff:
- Look for obstructions. A rake handle, a bike tire, a box or even a buildup of leaves at the threshold can stop the door or trigger a reversal.
- Try the wall button. If the wall button works but the remote doesn’t, the problem is the remote or its signal, not the door.
- Check the lock. Some doors have a manual slide lock or the opener may be in “lock” or “vacation” mode, which disables remotes.
- Confirm power. Make sure the opener is plugged in and the outlet or breaker hasn’t tripped.
Common Reasons a Garage Door Won’t Close
1. Blocked or Misaligned Safety Sensors
This is the most common cause. Every modern opener has two photo-eye sensors near the bottom of the tracks that send an invisible beam across the opening. If the beam is interrupted, the door won’t close, or it will reverse partway down. Typical signs: the door goes back up after a few inches, and the opener light blinks.
What to check: wipe the lenses with a soft cloth, make sure nothing is in the beam’s path, and confirm both indicator lights are on and steady. If one light is off or flickering, gently adjust that sensor until it lines up with the other. Loose or damaged sensor wires are another culprit. Morning fog and damp air around San Francisco can also leave condensation on the lenses, so a quick wipe is worth trying first.
2. Remote or Keypad Problems
If the door closes from the wall button but not from the remote, try fresh batteries and make sure you’re within range. If that doesn’t help, the remote may need to be reprogrammed to the opener, or the keypad may have failed. Our remote and keypad repair service can sort out stubborn signal issues.
3. Limit Settings Are Off
The opener’s limit settings tell it how far the door should travel. If the down limit is set too high, the door stops short or hits the floor, thinks it found an obstacle, and reverses. This can happen after a power surge, a new opener install or seasonal changes. Many openers let you adjust limits with buttons or dials, and your owner’s manual will show how. Make small adjustments and test after each one.
4. Close-Force Sensitivity
Openers measure resistance as the door moves. If the force setting is too sensitive, normal friction can make the opener reverse. Turning the force up is not a cure-all, though: if the door is binding because of a mechanical problem, more force just hides the issue and makes the safety reversal less reliable. If you have to keep raising the force, something else is wrong.
5. Damaged or Bent Tracks and Worn Rollers
Tracks that are bent, loose or out of alignment can make the door stick or rub. Worn rollers do the same. Look along both tracks for dents, gaps or debris, and watch the rollers as the door moves. Minor debris can be cleaned out, but bent tracks or a door that’s partly off its rollers needs professional attention. See our off-track and cable repair service for more.
6. Broken Spring or Cable
Springs carry the weight of the door. When one breaks, the door may be crooked, extremely heavy, or the opener may strain and stop. Frayed or snapped cables cause similar symptoms. If you see a gap in a torsion spring above the door, a loose cable or a door that hangs unevenly, stop using the opener. These parts are under high tension and are dangerous to handle without proper tools and training.
7. Opener Trouble
If the motor hums but the door doesn’t move, or the opener makes grinding noises, a gear, trolley or circuit board may have failed. Older openers, especially those without a safety reversal system that works reliably, may be due for replacement.
How to Close the Door Manually (Safely)
If you need to secure your garage right away and the door is otherwise in good shape, you can disconnect the opener and close it by hand:
- Make sure nothing and no one is under the door.
- If possible, have the door fully closed or fully open before releasing, because a partly open door can drop quickly if a spring is weak.
- Pull the red emergency release cord.
- Lower the door slowly by hand and lock it.
Don’t use the manual release if a spring or cable is visibly broken or the door is crooked. In that case, leave the door where it is and call for help.
When to Call a Pro
Some fixes are fine for a homeowner, like cleaning sensors, changing remote batteries or clearing debris. Call a technician if you notice any of the following:
- A broken or stretched spring, or a frayed or loose cable
- Bent tracks or a door that has come off its rollers
- A door that hangs crooked or feels very heavy when lifted by hand
- Grinding, popping or straining sounds from the opener
- The door still won’t close after you’ve checked the sensors and settings
Our team handles garage doors that won’t open or close across San Francisco and the greater Bay Area, including urgent situations where your garage can’t be secured.
Garage Door Won’t Close: FAQ
Why does my garage door close a little and then go back up?
Most often the safety sensors are blocked, dirty or misaligned, or something is in the door’s path. If the sensors check out, the opener’s close-force or limit settings may need adjusting, or a binding track or roller may be making the opener think it hit an obstruction.
Is it safe to leave my garage door open if it won’t close?
It is better to secure it. If the door is in good condition you can pull the emergency release and close it by hand, then lock it. If a spring or cable is broken, or the door is crooked, leave it alone and call a technician, because the door can drop or fall out of the tracks.
Why does my garage door only close when I hold the wall button?
Holding the wall button overrides the safety sensors on most openers. If that is the only way the door closes, the sensors are almost always the problem: check alignment, clean the lenses and look for damaged wiring.
Can a broken spring stop a garage door from closing?
Yes. A broken spring can leave the door crooked, too heavy for the opener, or stalled partway. Do not try to force it or work on the springs yourself; spring repair should be handled by a professional.
Get Your Garage Door Closing Again
If your garage door won’t close and the quick checks didn’t solve it, we can help. Call Bay Area Garage Doors at (415) 323-6329 or request an estimate online. We’re available 24/7 for garage door repair throughout the Bay Area.